wikiATP A600Vc M.2 2280 SATA SSDs
Dieser Artikel enthält Detail-Informationen zur 128 GB ATP A600Sv M.2 2280 SATA SSD. Diese SSD ist auf Lese-intensive Anwendungen zugeschnitten und kann in zahlreichen Thomas-Krenn-Systemen beispielsweise als Boot-Drive eingesetzt werden - siehe M.2 und mSATA SSDs in Thomas-Krenn Servern. Weitere SSDs von ATP zeigt der Artikel ATP SSDs im Überblick.
Allgemeine Informationen
Modell
| Capacity | Endurance | Throughput up to
(clean state) |
IOPS up to
(clean state) | ||||
|---|---|---|---|---|---|---|---|
| Random
Write (JEDEC Client) |
Sequential
Write |
Read | Write | Read | Write | ||
| AF128GSTIC-TM2 | 128 GB | 192 TBW | 349 TBW | 560 MB/s | 495 MB/s | 54 K | 90,5 K |
Firmware Versionen
| Version | Beschreibung |
|---|---|
| SBFMT1.3 | Initial Firmware |
Programmausgaben
smartctl
Für den Aufruf von smartctl wurde eine aktualisierte drivedb.h verwendet.[1]
root@debian12:~# smartctl -a /dev/sda
smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.0-9-amd64] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: ATP SATA III Value Line SSDs
Device Model: ATP SATA III M.2 2280
Serial Number: 22090027-000001
LU WWN Device Id: 0 000000 000000000
Firmware Version: SBFMT1.3
User Capacity: 128,035,676,160 bytes [128 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: M.2
TRIM Command: Available
Device is: In smartctl database
ATA Version is: ACS-4 (minor revision not indicated)
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon Jun 19 09:01:46 2023 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (65535) seconds.
Offline data collection
capabilities: (0x79) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 30) minutes.
Conveyance self-test routine
recommended polling time: ( 6) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Count 0x000b 100 100 050 Pre-fail Always - 0
9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 5
12 Power_Cycle_Count 0x0012 100 100 000 Old_age Always - 21
168 SATA_PHY_Error_Count 0x0012 100 100 000 Old_age Always - 0
170 Bad_Bl_Ct_LATER_0_EARLY 0x0003 100 100 010 Pre-fail Always - 0 0 83
173 Erase_Count_0_AVG_MAX 0x0012 100 100 000 Old_age Always - 0 0 1
192 Unexpected_Power_Loss 0x0012 100 100 000 Old_age Always - 7
194 Temperature_Celsius 0x0023 067 067 000 Pre-fail Always - 33 (Min/Max 33/33)
218 CRC_Errors 0x000b 100 100 050 Pre-fail Always - 0
231 Percent_Lifetime_Remain 0x0013 100 100 000 Pre-fail Always - 100
241 Host_Writes_GiB 0x0012 100 100 000 Old_age Always - 35
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
hdparm
root@debian12:~# hdparm -I /dev/sda
/dev/sda:
ATA device, with non-removable media
Model Number: ATP SATA III M.2 2280
Serial Number: 22090027-000001
Firmware Revision: SBFMT1.3
Transport: Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0
Standards:
Supported: 11 10 9 8 7 6 5
Likely used: 11
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 250069680
LBA48 user addressable sectors: 250069680
Logical Sector size: 512 bytes
Physical Sector size: 512 bytes
Logical Sector-0 offset: 0 bytes
device size with M = 1024*1024: 122104 MBytes
device size with M = 1000*1000: 128035 MBytes (128 GB)
cache/buffer size = unknown
Form Factor: unknown (0x0007]
Nominal Media Rotation Rate: Solid State Device
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
SET_MAX security extension
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
* WRITE_UNCORRECTABLE_EXT command
* {READ,WRITE}_DMA_EXT_GPL commands
* Segmented DOWNLOAD_MICROCODE
* Gen1 signaling speed (1.5Gb/s)
* Gen2 signaling speed (3.0Gb/s)
* Gen3 signaling speed (6.0Gb/s)
* Native Command Queueing (NCQ)
* Phy event counters
* READ_LOG_DMA_EXT equivalent to READ_LOG_EXT
* DMA Setup Auto-Activate optimization
* Device-initiated interface power management
* Software settings preservation
* DOWNLOAD MICROCODE DMA command
* SET MAX SETPASSWORD/UNLOCK DMA commands
* WRITE BUFFER DMA command
* READ BUFFER DMA command
* DEVICE CONFIGURATION SET/IDENTIFY DMA commands
* Data Set Management TRIM supported (limit 8 blocks)
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
supported: enhanced erase
20min for SECURITY ERASE UNIT. 60min for ENHANCED SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 0000000000000000
NAA : 0
IEEE OUI : 000000
Unique ID : 000000000
Checksum: correct
Einzelnachweise
- ↑ drivedb.h: Add ATP SATA III SSDs (github.com/smartmontools)
 |
Autor: Werner Fischer Werner Fischer arbeitet im Product Management Team von Thomas-Krenn. Er evaluiert dabei neueste Technologien und teilt sein Wissen in Fachartikeln, bei Konferenzen und im Thomas-Krenn Wiki. Bereits 2005 - ein Jahr nach seinem Abschluss des Studiums zu Computer- und Mediensicherheit an der FH Hagenberg - heuerte er beim bayerischen Server-Hersteller an. Als Öffi-Fan nutzt er gerne Bus & Bahn und genießt seinen morgendlichen Spaziergang ins Büro.
|
Das könnte Sie auch interessieren
ATP N600Sc M.2 NVMe SSDs mit PLP
ATP N600Sv M.2 NVMe SSD
Currently unreadable (pending) sectors - SMART-Daemon Proxmox
