Kontrolery RAID Adaptec serii 8 (12 Gb)
Przejdź do nawigacji
Przejdź do wyszukiwania
W tym artykule znajdują się informacje o kontrolerach RAID Adaptec serii 8 SAS/SATA 12 Gb. Przegląd wszystkich generacji kontrolerów RAID firmy Adaptec znajduje się w artykule Kontrolery RAID Adaptec.
Ogólne informacje
- Seria kontrolerów RAID: Adaptec 8 SAS/SATA 12 Gb
- Interfejs: 12Gb/s SAS/SATA / PCIe Gen3
- Format: low profile (śledź low profile i full profile)
- Dalsze informacje:
- Adaptec Series 8 RAID Controllers Review (storagereview.com, 07.02.2014)
- Adaptec by PMC ASR-8885 12Gb/s RAID Controller Review (tweaktown.com, 18.11.2013)
Modele
Kontroler RAID | Porty wew. |
Porty zew. |
PCIe lanes | Cache | Ochrona cache'a | Poziomy RAID | Maks. ilość HDD z użyciem expandera SAS |
Uwagi |
---|---|---|---|---|---|---|---|---|
Adaptec RAID 8405 | 4 | - | 8 | 1024MB | opcjonalnie (ZMCP) | 0, 1, 1E, 5, 6, 10, 50, 60 | 256 | |
Adaptec RAID 8805 | 8 | - | 8 | 1024MB | opcjonalnie (ZMCP) | 0, 1, 1E, 5, 6, 10, 50, 60 | 256 | |
Adaptec RAID 8885 | 8 | 8 | 8 | 1024MB | opcjonalnie (ZMCP) | 0, 1, 1E, 5, 6, 10, 50, 60 | 256 | |
Adaptec RAID 81605Z | 16 | - | 8 | 1024MB | moduł ZMCP zawarty w zestawie | 0, 1, 1E, 5, 6, 10, 50, 60 | 256 | |
Adaptec RAID 8885Q | 8 | 8 | 8 | 1024MB | moduł ZMCP zawarty w zestawie | 0, 1, 1E, 5, 6, 10, 50, 60 | 256 | maxCache Plus |
Adaptec RAID 81605ZQ | 16 | - | 8 | 1024MB | moduł ZMCP zawarty w zestawie | 0, 1, 1E, 5, 6, 10, 50, 60 | 256 | maxCache Plus |
Informacje
Build 33456 (22 May 2020)
- obsługuje kontrolery RAID serii 8
- Release Notes Build 33456, wyciąg z Fixes and Enhancements:
- Fixed a SATA drive drop issue when drive times out an IO followed by TUR command failure upon drive reset.
- Fixed an issue where host memory can get corrupted when SATA drive is stuck in NCQ error state during IO timeout error handling.
- Fixed an occasional issue where RAW drives were not exposed to OS after a drive swap during reboot.
Build 33401 (26 Aug 2019)
- obsługuje kontrolery RAID serii 8
- Release Notes Build 33401, wyciąg z Fixes and Enhancements:
- Enabled parallel rebuilds on overlapping logical drive configurations.
- Fixed an issue where the controller would assert during logical drive deletion.
- Fixed an issue where the drive slot/bay number was not listed correctly on few sepless expander configuration.
- Fixed an issue where RAID-configured disk will be exposed to OS after exchanging drive slots with raw state disk.
- Fixed an issue in PBSI interface where a drive part of a failed array is reported as 'Ready' state drive.
- Fixed a NVSRAM content loss issue during a minor dirty shutdown window.
- Fixed an issue where product revision of SATA drives are not reported correctly.
- Fixed an occasional exception when copyback task terminates.
- Fixed an issue where PBSI interface reports an incorrect GB status as READY when there are NAND-related errors.
Build 33303 (30 Jan 2019)
- obsługuje kontrolery RAID serii 8
- Release Notes Build 33303, wyciąg z Fixes and Enhancements:
- Fixed an issue where RAID 5 Copyback could take up to 15 times longer than Rebuild to complete.
- Fixed an issue where a command timeout would lead to an IOP reset.
- Fixed an issue where a single bad drive would cause drive discovery failure.
- Fixed an issue where ARC firmware history logs could be lost if firmware assert and power loss.
- Fixed an issue where ARCCONF setstatsdatacollection returned the wrong status, but command is actually successful.
- Fixed an issue where the UEFI Boot Option Priorities field displayed bad characters.
Build 33263 (12 Apr 2018)
- obsługuje kontrolery RAID serii 8
- Release Notes Build 33263, wyciąg z Fixes and Enhancements:
- Fixed an issue where the device was not detected after a hot-add.
- Fixed an issue where a drive command timeout could cause the adapter to reset.
- Fixed an issue where a redundant logical drive could fail after single drive failure.
- Fixed an issue where the firmware would crash after a rebuild with maxCache enabled.
- Fixed an issue where the logical drive would fail when a metadata write failed during rebuild.
Build 33204 (17 Oct 2017)
- obsługuje kontrolery RAID serii 8
- Release Notes Build 33204, wyciąg z Fixes and Enhancements:
- Added support for physical drive failure events through PBSI event logging.
- Fixed an issue where the console showed a controller cache warning due to a backup unit fault after flashing new firmware in UEFI mode.
- Fixed an issue where the drive would go offline during an expander reset operation.
- Fixed expander mapping issues.
- Fixed an issue where the Read Buffer would fail.
- Fixed an issue where the controller would hang when the drive member was removed from a RAID 5 array.
- Fixed an issue where the UEFI would freeze while saving the support archive.
- Added support for driver NMI feature to controllers.
- Fixed an issue where the INQUIRY to VPD page 0xB0 WRITE SAME length was leading to IO timeouts.
- Set the SES, STE, SVPD to a higher priority.
Build 33173 (30 Jun 2017)
- obsługuje kontrolery RAID serii 8
- Release Notes Build 33173, wyciąg z Enhancements and Bug Fixes:
- Resolved an issue where unexpected system reboots would occur during Windows 2012 I/O stress testing.
- Resolved an issue where the controller would stop responding during a RAID migration.
- Resolved an issue discovered when a drive is hot-plugged to replace a failed drive.
- Added support for Ubuntu 14.04.5, XenServer 7.0, RHEL 7.3, SLES 12 SP2, VMware 6.5.
- Resolved an issue where the system could crash with driver version 1.2.1-53005 and kernel version 3.10.101.
- Improved controller reset recovery.
- Fixed the Windows 2016 Server hang issue, when devices become unresponsive.
- Added support for vSphere 6.5 web client plugin.
Build 33083 (30 Jan 2017)
- obsługuje kontrolery RAID serii 8
- Release Notes Build 33083, wyciąg z Enhancements and Bug Fixes:
- Fixed an issue where the OS kernel panicked when removing the AACRAID driver.
- Fixed an issue where the driver was reporting the adapter dead in case of a SCSI hang.
- Fixed an issue where controller firmware lockup was encountered on the system while deleting units.
- Fixed an issue where customers on Ubuntu/Debian distributions did not have the documentation for building and installing the driver from the source.
- Fixed an issue where VMware was displaying a PSOD (purple screen) when the driver triggered an IOP reset.
- Improved the controller reset/recovery mechanism in Linux.
- Added support for SAS transport in the driver.
Build 30033 (04 Aug 2014)
- (Initial Firmware)
- obsługuje kontrolery RAID serii 7 i 8
- Release Notes Build 32033, wyciąg z Enhancements and Bug Fixes:
- New product release of the Adaptec RAID 8405 controller
- Added support for up to 128 Simple Volumes
- Re-enabled 16/32K Stripe size support
- Enhanced Error Analysis & Recovery
- Added support for global device write cache setting force off
Uwagi
Autor: Thomas Niedermeier
Powiązane artykuły
Instalacja systemu Windows na kontrolerze RAID firmy Adaptec w trybie UEFI
Kontrolery RAID Adaptec
Kontrolery RAID Adaptec serii 5 (3 Gb)