Intel® Modular Server System MFSYS25/MFSYS35 P2.6 Unified Firmware Update Release Notes & Installation Instructions February 12, 2009 RELEASE NOTES FOR: P2.6 A. RELEASE PACKAGE CONTENTS This section enumerates the contents of the release package. • BIOS: SB5000.86B.10.10.0048.100920081914 • BMC: 1.34.9 • Management Module GUI operation Code: 2.6.100.20081120.14717 • Remote KVM Java Applet – 1.40 • EBF: 1.26 • Storage • IOP FW/SW: 3.00.0140.77 • IOP SW: 3.00.0140.77 • Expander FW: 1.03.0140.66 • Redboot image: 1.01.0140.10 • Switch Boot Code: 1.0.0.6 • Switch FW: 1.0.0.27 • Fan Controller Op code – 01.2 • Fan Controller Boot Block – 01.2 • MIB files • Readme - Updated section "D. Defects Fixed in this Release" and section "G. Known Issues" B. GENERAL INFORMATION This release does not support rollback to previous version of the Unified Firmware Update (UFU) package. This release supports MFSYS25 system configurations with two SCMs for Microsoft® Windows 2003 R2 SP2, Microsoft® Windows 2008, and Suse Linux Enterprise 10 U1. Dual SCM operation is not supported in this release for the Redhat Enterprise Linux 5 operating system. This release supports MFSYS35 system configurations with single SCMs only in Slot SCM1 for all supported Operating Systems. C. DEPENDENCIES The system must be at firmware level P2.3.1 or P2.3.5 prior to starting this update. If the system contained two SCMs at firmware level P2.3.1 or P2.3.5, this update can continue with both SCMs installed. If you intend to install a second SCM to a system which previously contained only one SCM, the second SCM should be installed after the system has been updated to P2.6. After the firmware update has been completed, insert the second SCM into SCM2 slot. After installation of the second SCM, the system will then start an update for the firmware of the second SCM and expander on the interposer. Please see instructions for 2nd SCM installation and firmware update process in the Install Second SCM in SCM2 Slot section below. The update process will take approximately 15 – 20 minutes for the second SCM and should not be interrupted. D. DEFECTS FIXED IN THIS RELEASE Area | Description ----------------------------------------------------------------------------CMM GUI Enhanced the power supply cooling algorithm CMM GUI Clicking on a shared drive in Internet Explorer 6 or 7 sometimes does not change selected component CMM GUI Added new policies to handle event 0xe2 CMM GUI Power Supply Blank events were reported as Power supply events CMM GUI Communications test incorrectly treated non-zero IPMI result codes as failures CMM GUI GUI does not report the World Wide Number (WWN) of each Compute Module CMM GUI SNMP configuration page permits blank entries causing an invalid snmpd.conf CMM GUI hapiException when trying to assign virtual drive while a server module is unfit CMM GUI Time estimate added to storage pool expansion dialog CMM GUI The detail description for the SEL log of "SMI Timeout: Deasserted" changed to “The System Management Interrupt has been de-asserted”.. SCM Fujitsu SAS Drive intermittently will not be recognized by system after insertion BIOS [SMBIOS]Type 20 Starting and Ending Address are incorrect Driver MPIO driver fails to install under Windows 2008 Enterprise 64-bit SP1E. NEW FEATURES/FUNCTIONS IMPLEMENTED IN THIS RELEASE • 3.5” single SCM SAS or SATA storage subsystem - Mixing SAS and SATA drives in a chassis is not supported. • Shared LUN – This is a software key enabled feature. The following operating systems are supported: o Microsoft Windows Server 2008* (32bit and 64 bit) o SuSE* Linux Enterprise Server 10 U1 (32 bit and 64 bit) o VMware* ESXi 3.5 U3, VMware* ESX 3.5 U3 • Software key support – New functionality to support additional features via a software license key. • Dual controller support for Suse Enterprise Linux 10 U1 – SLES 10 U1 dual controller support with fail over fail back. • VMWare 3.5 U3 support – Dual SCM support with fail over fail back. • Multi-language support for online help – Added Russian and simplified Chinese versions of help. • Updated system cooling – Enhanced system cooling algorithms. • Cooling algorithm in the EBF - The CMM EBF can now run the cooling algorithm. • Multi power on/off server modules - Ability to power on/off multiple server modules in one operation • Server failover - Ability to reassign all LUNs from one server to another and power on the target server, all in one operation. Allows a user at a remote site to quickly get a standby server going if a particular server is down. • Data migration from PFA drives - If a drive gets marked as Predictive Failure Alert, and if there was no spare drive for that storage pool, the new feature allows the user to start a data migration manually. • BIOS customization in FW bundle - We now allow OEMs to modify the BIOS using standalone utilities and package it into the FW before applying the update to the chassis. • Drive cache enable – Ability to turn on drive write back cache for all drives within the chassis. • Send test email/snmp - Allows the user to test the snmp and email settings without waiting for a failure to happen. F. FEATURES/FUNCTIONS NOT YET IMPLEMENTED • MFSYS35 - 3.5” Chassis Dual SCM support - This configuration is not yet supported. • MFSYS25/MFSYS35 - Mixed SAS / SATA – This release does not support mixed SAS and SATA HDDs within a chassis. G. KNOWN ISSUES • SuSE* Linux Enterprise Server 10 U1 - SuSE* Linux Enterprise Server 10 U1 will mark the OS LUN as read only if a SCM affinity change is made while the SUSE* Linux Enterprise Server 10 operating system is running or booted. Workaround: Power down the SuSE* Linux Enterprise Server 10 U1 operating system. While the operating system is powered down go into the CMM UI and change the LUN affinity. • Ethernet Switch Module Hot-Swap - If you insert an Ethernet switch module into slot 1 or slot 2 in a chassis that is in steady state (no FW updates in progress or pending, and the chassis is operating normally), and if the ESM is not at the FW level 1.0.0.27, the CMM’s attempt to update the FW on the switch will not succeed. The FW update page will show that a FW update is ‘pending’. Resetting the switch or re-inserting the switch will not help. You have to reset the CMM. The FW update will be applied to the switch when the CMM restarts. This applies to ESM1 and ESM2. Note: This erratum applies only to ESM hot-insert. If you install the P2.6 UFU on a chassis that already has an ESM that is not at FW level 1.0.0.27, the FW update will happen without requiring additional CMM restarts. • Reset BIOS default settings – Certain settings and features such as Remote USB (essential for proper Remote KVM operation) may not be functional until BIOS Defaults are loaded. To ensure proper operation, reset BIOS defaults as soon as possible after updating BIOS. BIOS defaults are set by pressing F9 (Reset To Defaults) while in BIOS Setup. • GUI inconsistencies with physical state - The GUI can be inconsistent with the state of the system because this is a web application. If you suspect an inconsistency, just reload the page (the page automatically refreshes once a minute). Some HW inventory changes (such as compute module insertion) can take up to 60 seconds to be reflected in the GUI unless you push the refresh button. The application may also appear inconsistent with the real state of the system if you have connectivity issues with the CMM. • Complete System Diagnostics – Under synthetic stress test it is possible although rare for the SCM to reset if the user requests an All Subsystems diagnostics also called Complete System diagnostics. Prior to running the All Subsystems diagnostics feature the user should first power off all server modules within the chassis to guarantee that this issue is not encountered. • MIB Files - MIB files provide read only access to system information. System management and configuration are handled via the Modular Server Control GUI. Read/Write access will be available in future release. • Remote applications: 1. When starting rKVM with a Linux host, you must change the mouse mode to relative mode. If the remote mouse does not respond to local mouse movements, try switching to absolute mode and then immediately back to relative mode. 2. Due to the way Linux handles the mouse (relative vs. absolute) there are instances when the remote mouse on a Linux host will be slow or appear to stop functioning. Many times a stuck mouse can be awakened by toggling between relative and absolute mouse modes via the menu or the keyboard by pressing Alt-s. 3. If the local and remote mouse pointers do not synchronize (the remote mouse moves but is offset from the local mouse), try toggling the Synchronize mouse option. If that does not work, check the mouse acceleration parameters on the server with the command “xset q”. Set the mouse acceleration settings in Remote KVM in the Options menu to match those on the server. By default, the Remote KVM application will use an acceleration value of 2 and an acceleration threshold value of 4. These values are what the Red Hat Enterprise Linux Server 5 (RHEL5) and SuSE Linux Enterprise Server (SLES) operating systems expect, unless they have been modified after installation of the OS. 4. If the Internet connection is lost during an existing RKVM session, the session will report video data lost. The user must close the message, and restart the session. 5. Lost Keyboard/Mouse usage in SLES can sometimes be recovered by toggling full screen on and off. 6. Remote media is best used with one server at a time. If you map a CD to six compute modules, the compute modules will drop the CD mapping, due to latency issues. 7. The RKVM client version included in this release is 1.40. Check the version after installing the new release by launching the RKVM application and then using Help->About in the RKVM client window menus. If the version is something other than 1.40, close all RKVM client windows and delete the application from the client machine’s Java browser cache. (Run ‘javaws –viewer’, select the application titled ‘Networked KVM applet’ and press the delete key.) 8. Remote Floppy is not supported during a RKVM session. 9. Pressing F1 during a RKVM session will bring up the local KVM console help not the remote system application help. H. INSTALLATION INSTRUCTIONS Preparing For Update: • Download the current Unified Firmware Update package MFSYS25_MFSYS35_UFU_P2_6.zip for the MFSYS25/MFSYS35 system (including the MFS5000SI Compute Module). • Copy the CMM_Core.zip file to a folder labeled P2_6 on a formatted flash drive. CMM_Core.zip is the update package and is loaded as a zip file by the CMM Firmware Update tool. Do not modify the file name, otherwise it will not be recognized by the Update tool. • If you have not already done so, connect the appropriate power cords to the Intel® Modular Server System power supplies and wait for the chassis management module(CMM) to fully boot: approximately 3-4 minutes, when the CMM is fully booted the system cooling fans will slow down. • Prior to loading and using the P2.6 unified software update – all server modules in the system must be powered down. • If you intend to add a second SCM to the chassis as part of this update, please follow the procedures below for adding the second SCM in SCM slot 2. • Ensure that no Storage Pool or Virtual Drive build or rebuild operation is in progress. If a build, rebuild, or migration operation is in progress, allow the operation to complete before attempting to update the firmware via the Unified Firmware Update package. Unified Firmware Update from P2.3.1 or P2.3.5 to P2.6: 1. Launch a browser from a client system connected to the CMM 2. Login into the GUI and browse to the Firmware tab (bottom selection in the left navigation pane. 3. Ensure all servers are powered down, then click on the browse button and browse to the folder P2_6 you previously created, select the CMM_Core.zip file and the update will automatically begin. 4. The upload process will take several minutes – a progress bar is displayed. 5. After the file has been uploaded, the screen will display “A new Firmware File has been uploaded with build version 2.6.100.20081120.14717. 6. A box below this message labeled Actions will state – This update cannot be started until the following actions have been completed: Reset Storage Control Module 1 into Safe Mode. Click on the link. 7. It will then go to a screen that says Reset Controller SCM1 with a box checked that says “Come back in safe mode after reset.” Type CONFIRM and hit Apply. The screen will then display “Storage Controller resetting. This may take up to 4 minutes.” 8. It will then go to a screen that says “Reset of controller SCM1 to Safe Mode successful”. Hit OK. 9. If a second SCM is installed, repeat steps 6 – 8 to place the 2nd SCM into Safe Mode. 10. The screen will then return to the Firmware Update page, click on the “Start Update” button to continue. 11. A dialogue box will appear – select the “Reboot CMM & Start Update” button. (fans will speed up and then return to normal as the CMM restarts). The CMM will take 12 minutes to boot prior to displaying the Login screen. 12. Login to the GUI when prompted. Initial login may be slow due to firmware updates that are in progress. 13. Browse to the Firmware tab and scroll down to the Storage Controller line item. The Storage Controller 1 line item in the Firmware tab will indicate that the Storage Controller Module is updating to version 3.00.140.77. The update will take 5 - 10 minutes. Do not disturb the system while the update is in progress. While the update is still in process the Firmware tab will indicate that the Storage Controller Module is at 3.00.140.77. Do not interrupt the system while the system fans are at high speed. Wait until the system fans have returned to normal speed before verifying that all updates have been completed. Go to the system event log and verify that the following events have been logged: Server Power Permission Granted Storage Controller 1 Operational Storage Controller 2 Operational (dual SCM configurations). 14. Return to the firmware tab and verify that all updates have completed. 15. Do NOT move the SCM to slot 2 – it should remain in Slot 1 only for all future use. Complete BIOS Update (P2.3.1 – P2.6): 16. After verifying the BMC was updated on all servers, the BIOS status will show “Updates Pending – Power on required”. You can either click on the link, or follow the prompts to power on the server via the software OR you can manually power up all servers installed in the system via the front panel buttons. Note: Multiple servers can be powered on at the same time. The firmware update process can now update multiple servers at the same time. Attaching a monitor to each of the server modules during the BIOS update process enables you to monitor the BIOS update process. 17. A dialogue box will appear – Click “Apply” to power on servers. 18. Navigate to the Firmware screen. The status of each of the powered on server modules will show a BIOS Status of “Updates Pending (power on in progress)”. 19. Once the power on is complete the status may change to “Updates Pending - reset required”. DO NOT CLICK ON THIS LINK – wait a few minutes and the BIOS update will begin automatically. Only click on this link if you are able to verify that the update failed to start via a monitor attached to the modular server. 20. The BIOS status will eventually display “BIOS updating to SB5000.86B.10.10.0048….”. 21. Once the BIOS update has completed, the Firmware Status page in the GUI will show the BIOS status as “OK” and the version SB5000.86B.10.10.0048... will be displayed. 22. Repeat steps 16 – 21 for each server populated in the system. 23. Continue with steps below starting at step 24 under Verify Updates Completed and Load Defaults section. Verify Updates Completed and Load Defaults: 24. Enter BIOS setup on each server to verify BIOS update completed successfully and to load default settings. To restart a server and enter BIOS setup remotely using the Modular Server Control GUI follow the steps below: a. From the Server screen, select a server and restart the selected Server either by selecting the Reset action within the Modular Server Control GUI for the selected Server or from within the Remote KVM session. 25. On boot Enter BIOS Setup by pressing “F2” when prompted. 26. Verify the BIOS flashed successfully by entering BIOS setup, on the first tab, the “System BIOS” version displayed should be SB5000.86B.10.10.0048…. 27. Prior to loading default BIOS settings, document all custom BIOS settings. Then press F9 to load system default settings. Modify default settings as necessary to match documented custom settings previously used and Press F10 to save and exit. 28. Repeat steps 24 through 27 for each server to verify BIOS version and load default settings. Install Second SCM in SCM2 Slot: (Only required if adding second SCM) 29. Ensure that the appropriate steps have been taken per the Operating System BKM for upgrading to a second SCM prior to installing the second SCM. Power off all server modules prior to installing the second SCM. 30. Login to the GUI and browse to the Firmware tab (bottom selection in the left navigation pane. 31. Install the second SCM in SCM2 slot. 32. After the second SCM has booted, the firmware update page will either indicate “Firmware update to this component will begin soon” or “Update to version 3.00.140.77 queued”. 33. The second SCM line on the firmware tab will then indicate “updating to 3.00.140.77. The firmware update will take approximately 5 - 10 minutes. During this time the chassis fans will be at high speed and the chassis fault LED may illuminate. 34. The Firmware tab will then indicate that the second SCM has been updated to 3.00.140.77 however, the fans will remain at high speed and the chassis fault LED may remain illuminated. The Firmware tab will then indicate “updating expander”. Do not disturb the expander update process which will take approximately 10 minutes. 35. At the end of the expander update, a warning message at the top of the screen will indicate “Controller Fail-back in progress.” Storage Management functions may be temporarily unavailable. 36. The chassis fault LED will stop illuminating and the warning message at the top of the screen will disappear. 37. Browse to the event log. The event log should now display “Storage Controller Operational” for Storage Controller 2. LEGAL INFORMATION Information in this document is provided in connection with Intel Products and for the purpose of supporting Intel developed server boards and systems. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel’s Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Intel Corporation may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that relate to the presented subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied, by estoppel or otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights. Intel products are not intended for use in medical, life saving, or life sustaining applications. Intel may make changes to specifications and product descriptions at any time, without notice. Intel is a registered trademark of Intel Corporation. *Other names and brands are the property of their respective owners. Copyright © 2008 Intel Corporation.