MegaCLI Error Messages

Aus Thomas-Krenn-Wiki
Wechseln zu: Navigation, Suche

In diesem Artikel werden alle Fehlermeldungen (Error Messages) eines MegaRAID Controllers erläutert. Die Auflistung stammt aus dem MegaRaid SAS Software User Guide.[1]

MegaCLI Error Messages

0x00 Command completed successfully
0x01 Invalid command
0x02 DCMD opcode is invalid
0x03 Input parameters are invalid
0x04 Invalid sequence number
0x05 Abort isn't possible for the requested command
0x06 Application 'host' code not found
0x07 Application already in use - try later
0x08 Application not initialized
0x09 Given array index is invalid
0x0a Unable to add missing drive to array, as row has no empty slots
0x0b Some of the CFG resources conflict with each other or the current config
0x0c Invalid device ID / select-timeout
0x0d Drive is too small for requested operation
0x0e Flash memory allocation failed
0x0f Flash download already in progress
0x10 Flash operation failed
0x11 Flash image was bad
0x12 Downloaded flash image is incomplete
0x13 Flash OPEN was not done
0x14 Flash sequence is not active
0x15 Flush command failed
0x16 Specified application doesn't have host-resident code
0x17 LD operation not possibe - CC is in progress
0x18 LD initialization in progress
0x19 LBA is out of range
0x1a Maximum LDs are already configured
0x1b LD is not OPTIMAL
0x1c LD Rebuild is in progress
0x1d LD is undergoing reconstruction
0x1e LD RAID level is wrong for requested operation
0x1f Too many spares assigned
0x20 Scratch memory not available - try command again later
0x21 Error writing MFC data to SEEPROM
0x22 Required HW is missing (i.e. Alarm or BBU)
0x23 Item not found
0x24 LD drives are not within an enclosure
0x25 PD CLEAR operation is in progress
0x26 Unable to use SATA(SAS) drive to replace SAS(SATA)
0x27 Patrol Read is disabled
0x28 Given row index is invalid
0x2d SCSI command done, but non-GOOD status was received - see mf.hdr.extStatus for SCSI_STATUS
0x2e IO request for MFI_CMD_OP_PD_SCSI failed - see extStatus for DM error
0x2f Matches SCSI RESERVATION_CONFLICT
0x30 One or more of the flush operations failed
0x31 FW real-time currently not set
0x32 Command issues while FW in wrong state (i.e. GET RECON when op not active)
0x33 LD is not OFFLINE - IO not possible
0x34 Peer controller rejected request (possibly due to resource conflict)
0x35 Unable to inform peer of communication changes (retry might be appropriate)
0x36 LD reservation already in progress
0x37 I2C errors were detected
0x38 PCI errors occurred during XOR/DMA operation
0x39 Diagnostics failed - see event log for details
0x3a Unable to process command as boot messages are pending
0x3b Returned in case if foreign configurations are imcomplete
0x3d Returned in case if a command is tried on unsupported hardware
0x3e CC scheduling is disabled
0x3f PD CopyBack operation is in progress
0x40 Selected more than one PD per array
0x41 Microcode update operation failed
0x42 Unable to process command as drive security feature is not enabled
0x43 Controller already has a lock key
0x44 Lock key cannot be backed-up
0x45 Lock key backup cannot be verified
0x46 Lock key from backup failed verification
0x47 Rekey operation not allowed, unless controller already has a lock key
0x48 Lock key is not valid, cannot authenticate
0x49 Lock key from escrow cannot be used
0x4a Lock key backup (pass-phrase) is required
0x4b Secure LD exist
0x4c LD secure operation is not allowed
0x4d Reprovisioning is not allowed
0x4e Drive security type (FDE or non-FDE) is not appropriate for requested operation
0x4f LD encryption type is not supported
0x50 Cannot mix FDE and non-FDE drives in same array
0x51 Cannot mix secure and unsecured LD in same array
0x52 Secret key not allowed
0x53 Physical device errors were detected
0x54 Controller has LD cache pinned
0x55 Requested operation is already in progress
0x56 Another power state set operation is in progress
0x57 Power state of device is not correct
0x58 No PD is available for patrol read
0x59 Controller resert is required
0x5a No EKM boot agent detected
0x5b No space on the snapshot repositiry VD
0x5c For consistency SET PiTs, some PiT creations might fail and some succeed
0xFF Invalid status - used for polling command completion

Links

(für LSI 9261-8i SAS2 8x intern):

Einzelnachweise

  1. LSI User Guide Software

Das könnte Sie auch interessieren

CopyBack mit storcli manuell starten
Max-hw-sectors-kb bei MegaRAID Controllern anpassen
MegaRAID Festplatte im foreign Status wieder einbinden