Adaptec Series 8 RAID Controller 12 Gb

Aus Thomas-Krenn-Wiki
Zur Navigation springen Zur Suche springen

In diesem Artikel finden Sie Informationen zu Adaptec Series 8 SAS/SATA 12 Gb RAID Controllern. Alle Controller im Überblick zeigt der Artikel Adaptec RAID Controller.

Allgemeine Informationen

Modelle

RAID Controller Ports
intern		 Ports
extern		 PCIe Lanes Cache Cache-Schutz RAID-Level Max. Anzahl
SSDs/HDDs bei Verw.
von SAS Expandern		 Anmerkungen
Adaptec RAID 8405 4 - 8 1024MB Optional (ZMCP) 0, 1, 1E, 5, 6, 10, 50, 60 256
Adaptec RAID 8805 8 - 8 1024MB Optional (ZMCP) 0, 1, 1E, 5, 6, 10, 50, 60 256
Adaptec RAID 8885 8 8 8 1024MB Optional (ZMCP) 0, 1, 1E, 5, 6, 10, 50, 60 256
Adaptec RAID 81605Z 16 - 8 1024MB Inkludiert (ZMCP) 0, 1, 1E, 5, 6, 10, 50, 60 256
Adaptec RAID 8885Q 8 8 8 1024MB Inkludiert (ZMCP) 0, 1, 1E, 5, 6, 10, 50, 60 256 maxCache Plus
Adaptec RAID 81605ZQ 16 - 8 1024MB Inkludiert (ZMCP) 0, 1, 1E, 5, 6, 10, 50, 60 256 maxCache Plus

Versionsinformationen

Build 33552 (11 Dec 2020)

  • Unterstützt RAID Controller der Series 8
  • Release Notes Build 33552, Auszug aus Fixes and Enhancements:
    • Fixed an issue where the maxCache coherency check background task when enabled as "Always" does not reflect back the enabled settings value as "Always" in ARCCONF/maxView tools.
    • Fixed a controller hang issue due to IO with expiration time stamp that wraps around to zero.
    • Fixed an issue where the PBSI interface had a delayed update on a hot spare assignment event

Build 33456 (22 May 2020)

  • Unterstützt RAID Controller der Series 8
  • Release Notes Build 33456, Auszug aus Fixes and Enhancements:
    • Fixed a SATA drive drop issue when drive times out an IO followed by TUR command failure upon drive reset.
    • Fixed an issue where host memory can get corrupted when SATA drive is stuck in NCQ error state during IO timeout error handling.
    • Fixed an occasional issue where RAW drives were not exposed to OS after a drive swap during reboot.

Build 33401 (26 Aug 2019)

  • Unterstützt RAID Controller der Series 8
  • Release Notes Build 33401, Auszug aus Fixes and Enhancements:
    • Enabled parallel rebuilds on overlapping logical drive configurations.
    • Fixed an issue where the controller would assert during logical drive deletion.
    • Fixed an issue where the drive slot/bay number was not listed correctly on few sepless expander configuration.
    • Fixed an issue where RAID-configured disk will be exposed to OS after exchanging drive slots with raw state disk.
    • Fixed an issue in PBSI interface where a drive part of a failed array is reported as 'Ready' state drive.
    • Fixed a NVSRAM content loss issue during a minor dirty shutdown window.
    • Fixed an issue where product revision of SATA drives are not reported correctly.
    • Fixed an occasional exception when copyback task terminates.
    • Fixed an issue where PBSI interface reports an incorrect GB status as READY when there are NAND-related errors.

Build 33303 (30 Jan 2019)

  • Unterstützt RAID Controller der Series 8
  • Release Notes Build 33303, Auszug aus Fixes and Enhancements:
    • Fixed an issue where RAID 5 Copyback could take up to 15 times longer than Rebuild to complete.
    • Fixed an issue where a command timeout would lead to an IOP reset.
    • Fixed an issue where a single bad drive would cause drive discovery failure.
    • Fixed an issue where ARC firmware history logs could be lost if firmware assert and power loss.
    • Fixed an issue where ARCCONF setstatsdatacollection returned the wrong status, but command is actually successful.
    • Fixed an issue where the UEFI Boot Option Priorities field displayed bad characters.

Build 33263 (12 Apr 2018)

  • Unterstützt RAID Controller der Series 8
  • Release Notes Build 33263, Auszug aus Fixes and Enhancements:
    • Fixed an issue where the device was not detected after a hot-add.
    • Fixed an issue where a drive command timeout could cause the adapter to reset.
    • Fixed an issue where a redundant logical drive could fail after single drive failure.
    • Fixed an issue where the firmware would crash after a rebuild with maxCache enabled.
    • Fixed an issue where the logical drive would fail when a metadata write failed during rebuild.

Build 33204 (17 Oct 2017)

  • Unterstützt RAID Controller der Series 8
  • Release Notes Build 33204, Auszug aus Fixes and Enhancements:
    • Added support for physical drive failure events through PBSI event logging.
    • Fixed an issue where the console showed a controller cache warning due to a backup unit fault after flashing new firmware in UEFI mode.
    • Fixed an issue where the drive would go offline during an expander reset operation.
    • Fixed expander mapping issues.
    • Fixed an issue where the Read Buffer would fail.
    • Fixed an issue where the controller would hang when the drive member was removed from a RAID 5 array.
    • Fixed an issue where the UEFI would freeze while saving the support archive.
    • Added support for driver NMI feature to controllers.
    • Fixed an issue where the INQUIRY to VPD page 0xB0 WRITE SAME length was leading to IO timeouts.
    • Set the SES, STE, SVPD to a higher priority.

Build 33173 (30 Jun 2017)

  • Unterstützt RAID Controller der Series 8
  • Release Notes Build 33173, Auszug aus Enhancements and Bug Fixes:
    • Resolved an issue where unexpected system reboots would occur during Windows 2012 I/O stress testing.
    • Resolved an issue where the controller would stop responding during a RAID migration.
    • Resolved an issue discovered when a drive is hot-plugged to replace a failed drive.
    • Added support for Ubuntu 14.04.5, XenServer 7.0, RHEL 7.3, SLES 12 SP2, VMware 6.5.
    • Resolved an issue where the system could crash with driver version 1.2.1-53005 and kernel version 3.10.101.
    • Improved controller reset recovery.
    • Fixed the Windows 2016 Server hang issue, when devices become unresponsive.
    • Added support for vSphere 6.5 web client plugin.

Build 33083 (30 Jan 2017)

  • Unterstützt RAID Controller der Series 8
  • Release Notes Build 33083, Auszug aus Enhancements and Bug Fixes:
    • Fixed an issue where the OS kernel panicked when removing the AACRAID driver.
    • Fixed an issue where the driver was reporting the adapter dead in case of a SCSI hang.
    • Fixed an issue where controller firmware lockup was encountered on the system while deleting units.
    • Fixed an issue where customers on Ubuntu/Debian distributions did not have the documentation for building and installing the driver from the source.
    • Fixed an issue where VMware was displaying a PSOD (purple screen) when the driver triggered an IOP reset.
    • Improved the controller reset/recovery mechanism in Linux.
    • Added support for SAS transport in the driver.

Build 32033 (04 Aug 2014)

  • (Initiale Firmware für die Series 8 Controller)
  • Unterstützt RAID Controller der Series 7 und Series 8
  • Release Notes Build 32033, Auszug aus Enhancements and Bug Fixes:
    • New product release of the Adaptec RAID 8405 controller
    • Added support for up to 128 Simple Volumes
    • Re-enabled 16/32K Stripe size support
    • Enhanced Error Analysis & Recovery
    • Added support for global device write cache setting force off

Anmerkungen


Foto Thomas Niedermeier.jpg

Autor: Thomas Niedermeier

Thomas Niedermeier arbeitet im Product Management Team von Thomas-Krenn. Er absolvierte an der Hochschule Deggendorf sein Studium zum Bachelor Wirtschaftsinformatik. Seit 2013 ist Thomas bei Thomas-Krenn beschäftigt und kümmert sich unter anderem um OPNsense Firewalls, das Thomas-Krenn-Wiki und Firmware Sicherheitsupdates.

Icon-Twitter.png 

Das könnte Sie auch interessieren

Adaptec RAID Monitoring Plugin
Zum Artikel
Adaptec Series 6 RAID Controller 6 Gb
Zum Artikel
Festplattenausfall bei Adaptec RAID Controller mit ARCCONF beheben
Zum Artikel