Adaptec Series 7 RAID Controller 6 Gb

Aus Thomas-Krenn-Wiki
Zur Navigation springen Zur Suche springen

In diesem Artikel finden Sie Informationen zu Adaptec Series 7 SAS/SATA 6 Gb RAID Controllern. Alle Controller im Überblick zeigt der Artikel Adaptec RAID Controller.

Allgemeine Informationen

Modelle

RAID Controller Ports
intern
Ports
extern
PCIe Lanes Cache Cache-Schutz RAID-Level Max. Anzahl
SSDs/HDDs bei Verw.
von SAS Expandern
Anmerkungen
Adaptec RAID 7805 8 - 8 1024MB Optional (ZMCP) 0, 1, 1E, 5, 6, 10, 50, 60 256
Adaptec RAID 71605 16 - 8 1024MB Optional (ZMCP) 0, 1, 1E, 5, 6, 10, 50, 60 256
Adaptec RAID 71605E 16 - 8 1024MB Nein 0, 1, 1E, 10 256
Adaptec RAID 71685 16 8 8 1024MB Optional (ZMCP) 0, 1, 1E, 5, 6, 10, 50, 60 256
Adaptec RAID 72405 24 - 8 1024MB Optional (ZMCP) 0, 1, 1E, 5, 6, 10, 50, 60 256
Adaptec RAID 7805Q 8 - 8 1024MB Inkludiert (ZMCP) 0, 1, 1E, 5, 6, 10, 50, 60 256 maxCache 3.0
Adaptec RAID 71605Q 16 - 8 1024MB Inkludiert (ZMCP) 0, 1, 1E, 5, 6, 10, 50, 60 256 maxCache 3.0

Versionsinformationen

Build 30612 (13 Aug 2013)

  • Release Notes Build 30612, Auszug aus Enhancements and Bug Fixes:
    • Resolved an issue where I/O would slow and eventually result in a controller reset
    • Resolved an issue where RAID 1 members went missing if moved to different slots
    • Resolved an issue where set drive write cache command would fail using ARCCONF
    • Resolved an issue where drive firmware update would fail using maxView
    • Resolved an issue that would result in a drive dropping from the controller during an IOP reset
    • Resolved an issue that would cause inconsistent drive cache settings to be set
    • Resolved an issue where Series 7 controller would hang when UEFI HII was enabled on ASUS P8B-M/P8B-X/P9D-MH
    • Resolved an issue where hot-plug expander based enclosures and drives would not be properly discovered
    • Resolved an issue where alarm would not silence when alarm control mode was set to disabled in UEFI
    • Resolved an issue where USB keyboard would stop working if hot removed and re-inserted while in UEFI BIOS
    • Write performance enhancements
    • Resolved an issue where Series 7 controller was not detected during cold boot on some Asus/Tyan/Intel motherboards
    • Resolved an issue that prevented a RAW device from being configured as a bootable OS driv

Build 30260 (5 May 2013)

  • Release Notes Build 30260, Auszug aus Enhancements and Bug Fixes:
    • Added dual firmware image support
    • Super capacitor charge is now displayed in Host utilities
    • Added super capacitor lifetime prediction
    • Increased max outstanding IO to 1024, to improve performance on spinning disks on high queue depth random IO
    • Resolved an issue where Redhat 6.4 inbox driver would not load
    • Resolved an issue which would cause a corrupt GPT partition after reboot using 3 TB Raw Drive
    • Rebuilds no longer occur in parallel on multiple containers that share the same physical drives
    • Resolved an issue that would cause a controller kernel PANIC when a SC846Ex expander is attached
    • Resolved an issue where a RAID volume could not be deleted from BIOS
    • Resolved an issue where a failed array could not be deleted from BIOS
    • Fixed an issue where the controller cannot initialize with defective drive connected
    • Resolved an issue where Controller Kernel Stopped Running when attempting to create a RAID 10 using Clear Method
    • Resolved an issue where build/verify failed on the second logical drive after the first completed on the same physical drives
    • Fixed an issue that would lead to a firmware crash during the mkfs command on SLES 11 x64 SP2
    • Copyback implemented for uninitialized drive
    • Resolved an issue where Remote Arcconf (VMware ESXi 5.0) can’t delete the logical drives from Windows 7 x64 GuestOS.
    • Resolved an issue where SMC 846EL2(SAS2X36) with FW 0e0b would not detect any drive
    • Resolved an issue where a removed simple 'Volume' is not shown as 'offline'
    • Resolved an issue where controller alarm doesn’t stay on when hot removed enclosure with IO running
    • Resolved an issue where BIOS setting changes would not save after reboot
    • Resolved a firmware hang condition when performing Online Capacity Expansion on a RAID
    • UEFI Disk Utilities now shows pass or fail result/completion after disk verify
    • Changed message to Not supported (SES/SGPIO mode only) when attempting to Identify/blink drives on a passive backplane
    • Resolved an issue where blinking a drive would result in the wrong drive blinking in Promise enclosures
    • Resolved an issue where a RAID rebuild would not start if same drive was re-inserted
    • Resolved a controller hang issue when using the ACU utility to check on the build task progress of RAID-5 arrays
    • Resolved an issue with wrong status being reported after R6/R60 rebuild completes
    • Resolved an issue where RAID 0 maxCache Container is not converted to Simple Volume when there is a drive failure
    • Resolved an issue where incorrect array ID and RAID level were displayed in UEFI Manage Array menu
    • Resolved an issue where smartctl –x /dev/xxx fails on SATA drives
    • Modified messaging for Global Hot Spare in UEFI
    • Resolved an issue where SSDs partially used for a maxCache container were not available for RAID creation in UEFI
    • Changed spare messaging in HII
    • Resolved an issue where the bottom border was missing when displaying R50 or R60 with 7 members on each leg
    • Resolved an issue where CRC errors were causing drives to be marked offline
    • Resolved an issue where periodic performance drops would occur due to enclosure management communication
  • Adaptec maxView Storage Manager v1.02 Readme

Build 30040 (29 Jan 2013)

  • Release Notes Build 30040, Auszug aus Enhancements and Bug Fixes:
    • Resolved a possible GPT partition corruption issue when a drive greater than 2TB is configured as a RAW drive in a Linux OS on a Series7 controller in HBA mode.

Build 30035 (21 Dec 2012)

  • Release Notes Build 30035, Auszug aus Enhancements and Bug Fixes:
    • Resolved an issue that would prevent the installation of FreeBSD 9.0 when a Series 7 controller is set to HBA mode.
    • Resolved an issue that would prevent a Series 7 controller from being put into HBA mode.

Build 30032 (28 Nov 2012)

  • Release Notes Build 30032, Auszug aus Enhancements and Bug Fixes:
    • Resolved an issue with ARCCONF command line interface, Advance Statistics "Overall read(write) in MB" not reporting in the correct units.
    • Resolved an issue where SAS drives could potentially be marked as failed during a RAID creation following a system reboot.
    • Resolved an issue with ARCCONF command line interface, where "IO completion time" were incorrectly reported.
    • Resolved an issue where the AFM-700 incorrectly shows as "Not Ready" during POST when fully charged.
    • Resolved an issue that would prevent a system from booting if maxCache is disabled on a bootable array.
  • Adaptec maxView Storage Manager v1.0 Readme

Build 30021

  • (Initiale Firmware)

Anmerkungen


Autor: Franz Nemeth

Das könnte Sie auch interessieren

Adaptec arcconf CLI
Adaptec Firmwareupdate mit arcconf auf VMware Systemen
Adaptec Series 5 RAID Controller 3 Gb