Adaptec Series 7 RAID Controller 6 Gb

Aus Thomas-Krenn-Wiki
Zur Navigation springen Zur Suche springen

In diesem Artikel finden Sie Informationen zu Adaptec Series 7 SAS/SATA 6 Gb RAID Controllern. Alle Controller im Überblick zeigt der Artikel Adaptec RAID Controller.

Allgemeine Informationen

Modelle

RAID Controller Ports
intern
Ports
extern
PCIe Lanes Cache Cache-Schutz RAID-Level Max. Anzahl
SSDs/HDDs bei Verw.
von SAS Expandern
Anmerkungen
Adaptec RAID 7805 8 - 8 1024MB Optional (ZMCP) 0, 1, 1E, 5, 6, 10, 50, 60 256
Adaptec RAID 71605 16 - 8 1024MB Optional (ZMCP) 0, 1, 1E, 5, 6, 10, 50, 60 256
Adaptec RAID 71605E 16 - 8 1024MB Nein 0, 1, 1E, 10 256
Adaptec RAID 71685 16 8 8 1024MB Optional (ZMCP) 0, 1, 1E, 5, 6, 10, 50, 60 256
Adaptec RAID 72405 24 - 8 1024MB Optional (ZMCP) 0, 1, 1E, 5, 6, 10, 50, 60 256
Adaptec RAID 7805Q 8 - 8 1024MB Inkludiert (ZMCP) 0, 1, 1E, 5, 6, 10, 50, 60 256 maxCache 3.0
Adaptec RAID 71605Q 16 - 8 1024MB Inkludiert (ZMCP) 0, 1, 1E, 5, 6, 10, 50, 60 256 maxCache 3.0

Versionsinformationen

Build 30612 (13 Aug 2013)

  • Release Notes Build 30612, Auszug aus Enhancements and Bug Fixes:
    • Resolved an issue where I/O would slow and eventually result in a controller reset
    • Resolved an issue where RAID 1 members went missing if moved to different slots
    • Resolved an issue where set drive write cache command would fail using ARCCONF
    • Resolved an issue where drive firmware update would fail using maxView
    • Resolved an issue that would result in a drive dropping from the controller during an IOP reset
    • Resolved an issue that would cause inconsistent drive cache settings to be set
    • Resolved an issue where Series 7 controller would hang when UEFI HII was enabled on ASUS P8B-M/P8B-X/P9D-MH
    • Resolved an issue where hot-plug expander based enclosures and drives would not be properly discovered
    • Resolved an issue where alarm would not silence when alarm control mode was set to disabled in UEFI
    • Resolved an issue where USB keyboard would stop working if hot removed and re-inserted while in UEFI BIOS
    • Write performance enhancements
    • Resolved an issue where Series 7 controller was not detected during cold boot on some Asus/Tyan/Intel motherboards
    • Resolved an issue that prevented a RAW device from being configured as a bootable OS driv

Build 30260 (5 May 2013)

  • Release Notes Build 30260, Auszug aus Enhancements and Bug Fixes:
    • Added dual firmware image support
    • Super capacitor charge is now displayed in Host utilities
    • Added super capacitor lifetime prediction
    • Increased max outstanding IO to 1024, to improve performance on spinning disks on high queue depth random IO
    • Resolved an issue where Redhat 6.4 inbox driver would not load
    • Resolved an issue which would cause a corrupt GPT partition after reboot using 3 TB Raw Drive
    • Rebuilds no longer occur in parallel on multiple containers that share the same physical drives
    • Resolved an issue that would cause a controller kernel PANIC when a SC846Ex expander is attached
    • Resolved an issue where a RAID volume could not be deleted from BIOS
    • Resolved an issue where a failed array could not be deleted from BIOS
    • Fixed an issue where the controller cannot initialize with defective drive connected
    • Resolved an issue where Controller Kernel Stopped Running when attempting to create a RAID 10 using Clear Method
    • Resolved an issue where build/verify failed on the second logical drive after the first completed on the same physical drives
    • Fixed an issue that would lead to a firmware crash during the mkfs command on SLES 11 x64 SP2
    • Copyback implemented for uninitialized drive
    • Resolved an issue where Remote Arcconf (VMware ESXi 5.0) can’t delete the logical drives from Windows 7 x64 GuestOS.
    • Resolved an issue where SMC 846EL2(SAS2X36) with FW 0e0b would not detect any drive
    • Resolved an issue where a removed simple 'Volume' is not shown as 'offline'
    • Resolved an issue where controller alarm doesn’t stay on when hot removed enclosure with IO running
    • Resolved an issue where BIOS setting changes would not save after reboot
    • Resolved a firmware hang condition when performing Online Capacity Expansion on a RAID
    • UEFI Disk Utilities now shows pass or fail result/completion after disk verify
    • Changed message to Not supported (SES/SGPIO mode only) when attempting to Identify/blink drives on a passive backplane
    • Resolved an issue where blinking a drive would result in the wrong drive blinking in Promise enclosures
    • Resolved an issue where a RAID rebuild would not start if same drive was re-inserted
    • Resolved a controller hang issue when using the ACU utility to check on the build task progress of RAID-5 arrays
    • Resolved an issue with wrong status being reported after R6/R60 rebuild completes
    • Resolved an issue where RAID 0 maxCache Container is not converted to Simple Volume when there is a drive failure
    • Resolved an issue where incorrect array ID and RAID level were displayed in UEFI Manage Array menu
    • Resolved an issue where smartctl –x /dev/xxx fails on SATA drives
    • Modified messaging for Global Hot Spare in UEFI
    • Resolved an issue where SSDs partially used for a maxCache container were not available for RAID creation in UEFI
    • Changed spare messaging in HII
    • Resolved an issue where the bottom border was missing when displaying R50 or R60 with 7 members on each leg
    • Resolved an issue where CRC errors were causing drives to be marked offline
    • Resolved an issue where periodic performance drops would occur due to enclosure management communication
  • Adaptec maxView Storage Manager v1.02 Readme

Build 30040 (29 Jan 2013)

  • Release Notes Build 30040, Auszug aus Enhancements and Bug Fixes:
    • Resolved a possible GPT partition corruption issue when a drive greater than 2TB is configured as a RAW drive in a Linux OS on a Series7 controller in HBA mode.

Build 30035 (21 Dec 2012)

  • Release Notes Build 30035, Auszug aus Enhancements and Bug Fixes:
    • Resolved an issue that would prevent the installation of FreeBSD 9.0 when a Series 7 controller is set to HBA mode.
    • Resolved an issue that would prevent a Series 7 controller from being put into HBA mode.

Build 30032 (28 Nov 2012)

  • Release Notes Build 30032, Auszug aus Enhancements and Bug Fixes:
    • Resolved an issue with ARCCONF command line interface, Advance Statistics "Overall read(write) in MB" not reporting in the correct units.
    • Resolved an issue where SAS drives could potentially be marked as failed during a RAID creation following a system reboot.
    • Resolved an issue with ARCCONF command line interface, where "IO completion time" were incorrectly reported.
    • Resolved an issue where the AFM-700 incorrectly shows as "Not Ready" during POST when fully charged.
    • Resolved an issue that would prevent a system from booting if maxCache is disabled on a bootable array.
  • Adaptec maxView Storage Manager v1.0 Readme

Build 30021

  • (Initiale Firmware)

Anmerkungen


Autor: Franz Nemeth

Das könnte Sie auch interessieren

Adaptec RAID Controller in VMware überwachen mit MaxView Storage Manager
Festplattenausfall bei Adaptec RAID Controller mit ARCCONF beheben
Optionen beim Erstellen eines Adaptec RAID Arrays